Whirlpool hottub bathtub jet

Where to use Bathtub jet ?

The walls and bottom of the Bathtub are distributed over the nozzles, ranging from two to ten pairs. It is used in water for massage effect. Nozzles are roughly divided into two types, water spray and air jet. There are two types of water spray nozzles. One is to spray water from the nozzle through pipes and pumps; the other is Kaldewei's unique turbo nozzle, the first brand of Jacuzzi in Europe. Each nozzle has an independent motor, and water is drawn in around the nozzle and sprayed out the middle. The jets massage through the water. The nozzle itself does not produce water. It sprays airflow through the air pump and pipes, forming air bubbles in the water for massage. The nozzle has a strong massaging force compared to the nozzle. To increase the intensity and intensity of the massage, it is now common practice to install airflow in the nozzle. Generally speaking, simple nozzles are mounted on the cylinder wall and the nozzles are mounted on the bottom of the cylinder. The nozzles at the bottom of the cylinder are mainly used to massage the back. The nozzles on the cylinder wall are mainly used to massage the soles of the feet and the shoulders on both sides of the body. Bathtub are generally not standard. In combination with the Card Jacuzzi, there are at least 4 jets.

Understanding Your Choice Of bathtub jet

1. What is the function of bathtub jet?

The jets at the bottom of the bathtub do a great job

High Water Volume Quiet Adjustable Nozzle, 3/8" nozzle, 14gpm (gallons per minute) water output at 18psi (Pascals) with air switch fully open. This nozzle can produce approximately 10,000 small Air bubbles, small air bubbles are not easy to quickly float to the water surface and burst, so the water flow from the nozzle is strong but very soft. The nozzle massages the size of the water output, and the nozzle can be opened from the front to clean the inside of the nozzle. Double helix According to the nozzle, the unique swirling air bubbles and continuous vortex action create air and water flow in the same direction of rotation. Send a deep massage force, effectively relax the tense muscles and relieve pressure. The bubble massage system is passed through the bathtub by a bubble pump The air bubble nozzle at the bottom generates a large amount of air bubbles to wrap the whole body. Gently stroking the body can make the spine and neck feel comfortable, so that the muscles and body and mind can relax.

2. What are The Different Types Of bathtub jet?

There are basically two types of sprinklers, water spray and jet

Water spray: There are two types of spray nozzles, one is to spray water from the nozzle through pipes and pumps; the other is the unique turbo nozzle of Kaldewei, the first brand of European massage bathtubs. The sprinkler head has an independent motor, the water is sucked in from around the sprinkler head, and then sprayed from the middle, and the sprinkler head is massaged by the water flow.

Air jet: The jet nozzle itself does not contain water. It sprays air through air pumps and pipes, forming air bubbles in the water for massage. Compared with the jet nozzle, the massage force of the water jet nozzle is stronger. In order to increase the massage intensity and strengthen the court, the usual practice is to install airflow in the water nozzle.

3. What are the classifications of bathtubs

1. If divided according to function, some are ordinary types. There are many options for the length of this bathtub, such as some 1-2 mm, some 1700 mm, the width is between 700~900 mm, and the height is about 355~ 518mm. Some have a bathtub function with massage function, and the performance is more enhanced. Dimensions: The length is basically 1500 mm, the width is between 800 and 900 mm, and the height is generally 470 mm.

There is also a sitting bubble type, the length is basically 1100 mm, and the height is about 475. Of course, because it is a sitting bath, the sitting place can reach 300 mm.

2. If it is divided according to the shape, some are with skirts, and some are without skirts.

3. If divided according to material, some are made of enamel, and ceramics are divided into cast iron, including steel plate. Some are a kind of glass fiber reinforced plastic, and some are artificial agate or marble bathtubs. There are also wood types, and there are more general ceramics.

4. How to install the bathtub jet?

It must be installed by a qualified plumber.

2. Reserve distribution pipes and junction boxes during the construction of the square house.

3. For the power supply line, please reserve an independent loop power supply wiring according to the electrical engineering specifications or refer to the electrical wiring diagram. Make sure that the power supply is 110 volts, and the wire can withstand 15 amps of current (wire diameter 2.0 mm square or more), and the wire head outlet is the same as the motor. The direction is about 10cm above the ground, and an earth leakage circuit breaker is installed at the distribution box. If an independent circuit earth leakage circuit breaker is not installed in advance, it must be installed in a proper position, but it should not be installed under the bathtub.

4. Connect the power cord and cover the insulation. Note that the power connection should be connected before the bathtub is fixed and the front wall panel of the bathtub is filled with caulk, and the grounding wire should be grounded.

5. During the period when the construction site is not finished decoration, it is best not to connect the power cord of the motor properly. If the power cord needs to be connected properly due to the convenience of construction, the leakage circuit breaker switch must be turned off to prevent the motor from idling and burning out.

1. Trial operation: Turn on the faucet and wait until the water level of the bathtub is at least 100mm higher than the upper edge of the nozzle, then turn on the power switch to make the pump run. If it does not operate normally, please check whether the contacts are installed correctly and firmly.

5. How to maintainance bathtub jet ?

1. Do not use rough-surfaced utensils that contain chemical solvents or particles to clean the surface of the tub. Do not hit and scratch the surface of the bathtub with a hard object or a knife, and do not allow cigarette butts or heat sources higher than 70°C to touch the surface of the bathtub. After the bathtub is used, it should be drained and disconnected from the power source. 2. Cleaning of Jacuzzi For daily cleaning, general liquid detergent and soft cloth can be used, and detergents containing ketone or chlorine water cannot be used for cleaning. When disinfecting, disinfectants containing formic acid and formaldehyde are prohibited. The scale on the surface of the bathtub can be wiped with a soft cloth after adding a mild acid detergent, such as lemon juice and vinegar, after adding slight heat. If the surface of the cylinder is dirty, it can be wiped with a wet towel. This process can be repeated three times, and it can be as clean as new. If you use the hydraulic friction device for cleaning, pay attention to the steps: fill the bathtub with 40 ℃ hot water, add 2 grams of detergent per liter, start the hydraulic massage for about 5 minutes and stop the pump to drain. Then fill up with cold water, start the hydromassage for about 3 minutes, stop the pump to drain and clean the bathtub. If the water return device and the nozzle are blocked by hair, etc., just unscrew it and you can clean it. 3. Treatment of jacuzzi scratches The jacuzzi will inevitably have some scratches during use. If there are scratches on the surface, just use 2000# water abrasive paper to polish it, then apply toothpaste, and polish it with a soft cloth. new. In fact, the service life of many things is related to how to maintain them. We can turn a blind eye to cheap things, but we have to take care of large and expensive Jacuzzis. If the bathtub has a large area of ​​collapse, roughening, etc., it is best to ask a professional maintenance company to renovate the bathtub. Once the bathtub has been refurbished, it will return to the beautiful shiny finish it had when it was first purchased

6. Where to buy bathtub jet ?

So, a lot depends on making the right choice, how do you ensure you have the right tub spray for your project? Well, it's one thing to do your due diligence when buying a product, but you know very little about the manufacture of your bathtub accessories or the raw materials of the final product.

Suppliers typically make these decisions. That's why, in order to provide your own bathtub with higher quality, more comfort and beauty, with years of experience in the bathroom accessories industry, Luohe Global has the expertise to produce high-quality products with extremely cheap bathroom shower heads. Not only does this guarantee that your project is done to the highest safety standards, but the hot tub accessories you purchase will save you a lot of money. The result: a high-quality, low-cost, beautiful bathroom project! Contact us and you can become our bathroom accessories distributor. We will provide you with a price list！